Beschreibung
Description
The STLINK-V3MINI is stand-alone debugging and programming mini probe for STM32 microcontrollers.
The JTAG/SWD interfaces are used to communicate with any STM32 microcontroller located on an application board.
The STLINK-V3MINI also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART.
The STLINK-V3MINI is a portable version, easy-to-use debugger/programmer including STDC14 interface with its flat cable.
Key Features
- Stand-alone probe
- Approximately 15 x 30 mm high-density integration PCB, very small form factor
- Self-powered through a Micro-B USB connector (does not provide power supply to the target application)
- USB 2.0 high-speed compatible interface
- Direct firmware update (DFU) support, to use with more future devices
- JTAG / serial wire debugging (SWD) specific features:
- 3 V to 3.6 V application voltage support and 5 V tolerant inputs
- Delivered with 1.27 mm pitch STDC14 to STDC14 flat cable
- Additional adapter board and 2.54 mm pitch 20-pin JTAG/SWD flat cable (extra accessories from Waveshare)
- SWD and serial wire viewer (SWV) communication support
- Virtual COM port (VCP) specific features:
- 3 V to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs
- VCP frequency up to 15 MHz
- Drag-and-drop Flash programming
- Two color LEDs: communication, power
- Includes STDC14 signals protection
Supported Software
- STM32CubeProgrammer
- Keil® MDK-ARM
- IAR? EWARM
- SW4STM32
- STVP
- GCC-based IDEs
Supported Devices
- All STM32 MCUs with JTAG / SWD interface
Specification Comparison among Different STLINK Versions
Comparison | STLINK-V3SET | STLINK-V3MINI | ST-LINK/V2 | Remarks |
---|---|---|---|---|
JTAG/SWD application voltage | 3V - 3.6V | 3V - 3.6V | 1.65V - 3.6V | ST-LINK/V2 supports STM32 low-power devices |
SWIM application voltage | 1.65V - 5.5V | N/A | 1.65V - 5.5V | STLINK-V3MINI doesn't support SWIM of STM8 |
SWV support | YES | YES | YES | only available for STM32 at present |
Debug interface | multi | multi | 2 | STLINK-V3SET/MINI feature GPIO port besides the programming port |
LED indicator | two colors | two colors | two colors | two colors LED indicates both power and communication, while red color LED indicates only communication |
Example
Note: the STM32 application board in the photo is NOT included.
Connect to PC
The STLINK-V3MINI should be connected to the PC via a USB Micro-B cable.
- Before connecting, install/update the ST-LINK toolset to support the STLINK-V3MINI (drivers)
- STLINK-V3MINI adopts an STM32 F7 microcontroller, supports USB2.0 high speed communication
Connect to STM32 applications
The STLINK-V3MINI can be connected to STM32 target applications on JTAG / SWD interfaces.
- Connection Method A: connect to target application directly via the onboard STDC14 connector.
- Connection Method B: connect to target application via the STLINK-V3MINI Adapter board.
STLINK-V3MINI LED Status
- COM LED is blinking RED: the first USB enumeration with the PC is taking place.
- COM LED is RED: communication between STLINK-V3MINI and the PC is established (end of enumeration).
- COM LED is blinking GREEN/RED: data are being exchanged between the target and the PC.
Dimensions
Development Resources
Package Contents
- STLINK-V3MINI official content x1
- STLINK-V3MINI Adapter x1
- USB type A plug to micro B plug cable x1
- 20-pin JTAG/SWD flat ribbon x1
- 3-pin 2.54mm pitch squid wire x1
Versandgewicht: | 0,11 Kg |
Software
Artikel bewerten
Durchschnittliche Artikelbewertung
Verfügbarkeit
Lassen Sie sich per E-Mail benachrichtigen, sobald das Produkt wieder verfügbar ist:
Lassen Sie sich per E-Mail benachrichtigen, sobald das Produkt wieder verfügbar ist: