Formlabs Form Studio Wash+Cure

Artno.: FO1-148540
Manufacturers: Formlabs

The Form Studio Wash+Cure is an innovative and compact post-processing device that efficiently simplifies both the cleaning and curing of resin 3D printed parts in one step. With its 2-in-1 function and smart drying system, it optimizes the entire post-processing process and significantly improves part properties.

224,01 €

incl. 19% VAT

(188,24 € excl. VAT)

Orderable
Delivery time: ca. 3 months (DE - int. shipments may differ)

Description
Product Reviews

FORMLABS FORM STUDIO WASH+CURE

Formlabs Form Studio Wash+Cure

Compact all-in-one unit for post-processing resin prints – washing with circulating solvent and post-curing with 405 nm light in one device.

Washing and curing in one place

Every resin part has to be cleaned of liquid resin after printing and then post-cured to reach its final material properties. The Form Studio Wash+Cure combines both steps in one unit measuring 33 × 30 × 44 cm. It works with IPA, TPM or Formlabs Resin Washing Solution and is compatible with the Form Studio 1 as well as other Formlabs SLA printers.

Dynamic wash bath

A magnetically coupled impeller circulates solvent in the 10 L wash bucket, flushing liquid resin out of channels, cavities and undercuts. Parts can go in directly on the build platform or be placed in the wash basket. After the wash cycle, the basket is raised so parts drain and dry outside the solvent – preventing swelling and warping.

Magnetically coupled impeller

10 L wash bucket

Wash basket

Build platform fits directly

In-unit drying

IPA · TPM · Resin Washing Solution

405 nm

LED wavelength for post-curing

24 LEDs

Multi-directional, 48 W power

10 L

Wash bucket volume

24.5 cm

Max. part height

POST-CURING

Even exposure from every side

For curing, the glass turntable is placed in the chamber. As parts rotate, 24 multi-directional LEDs at 405 nm expose them evenly from all sides. Post-curing completes the chemical reaction that starts during printing and increases strength, toughness, heat resistance and creep resistance. The surface becomes harder and less tacky.

405 nm

24 multi-directional LEDs

Rotating turntable

24 cm turntable

No heating element

WORKFLOW

From printer to finished part

After printing, the build platform goes straight into the wash bucket, or parts are placed in the basket. The impeller moves the solvent and rinses off liquid resin. At the end of the cycle, the basket is raised for drying. Parts are then removed from the platform, placed on the turntable and post-cured under 405 nm light. The lidded wash bucket stores the solvent between uses.

Wash

Dry

Cure

Wash bucket with lid

For Form Studio 1

Highlights

Two steps, one unit

Washing and curing in one compact unit measuring 33 × 30 × 44 cm and weighing 10 kg.

Thorough cleaning

Circulating solvent reaches channels, cavities and undercuts.

Drying without transfer

Raise the basket after washing – parts drain and dry outside the solvent.

Even exposure

The rotating turntable ensures light reaches every side of the parts.

Common solvents

Compatible with IPA, TPM and Formlabs Resin Washing Solution.

Broad compatibility

For parts from Form Studio 1, Form 4, Form 4B, Form 3/+, Form 3B/+ and Form 2.

Technical Data

Product	Formlabs Form Studio Wash+Cure
Device type	All-in-one wash and post-cure unit for resin 3D prints
Compatible printers	Form Studio 1, Form 4, Form 4B, Form 3/+, Form 3B/+, Form 2
Dimensions	33 × 30 × 44 cm
Weight	10 kg
Wash bucket volume	10 L
Agitation method	Magnetically coupled impeller
Compatible solvents	IPA, TPM, Formlabs Resin Washing Solution
Light source	24 multi-directional LEDs
LED wavelength	405 nm
LED power	48 W
LED radiant power	27.84 W
Turntable diameter	24 cm
Max. part height	24.5 cm
Curing chamber temperature	No heating element
Power requirements	100–240 V AC, 50/60 Hz, max. 2 A, 200 W
Recommended operating environment	18–28 °C

Scope of Delivery

Unit	Form Studio Wash+Cure
Washing	Wash bucket with lid, wash basket
Curing	Curing turntable
Required separately	Solvent (IPA, TPM or Formlabs Resin Washing Solution)

Typical Applications

The Form Studio Wash+Cure is designed for users who want to post-process resin prints at their desk with a small footprint – for example as a companion to the Form Studio 1. It suits miniatures and figurines, models, props and prototypes, as well as parts with channels and cavities from which liquid resin must be reliably removed.

Miniatures

Figurines

Model making

Props

Prototypes

Hobby & studio

Form Studio 1

Complete post-processing in a small footprint

The Formlabs Form Studio Wash+Cure suits anyone who wants to clean resin parts thoroughly and fully post-cure them without separate wash and cure stations.

Notes on Use

Solvent is not included. When handling IPA and other solvents, follow the safety data sheets and manufacturer instructions. The curing chamber has no heating element; Formlabs recommends an operating environment of 18–28 °C. For two-stage washing, Formlabs offers the Form Studio Wash+Cure Rinse Bucket as an optional accessory.

FORMLABS AT WELECTRON

The Formlabs Form Studio Wash+Cure is available at Welectron.

Shipping weight:	10,52 kg

There are no reviews yet.